Marvel clear ice machine with every indicator flashing: boards not talking
Marvel's clear ice machine splits its electronics between a main control board and the user interface on the front.
Mon–Sat, 8am–8pm
- Control board and power
- Ice machine control board repair
- Source: Marvel
Book a visit
Three short steps, about a minute.
or call (844) 410-9163
Loading appointment form…
The appointment form couldn’t load. Please try again.
What All indicators flashing
actually means.
Marvel's clear ice machine splits its electronics between a main control board and the user interface on the front. When they stop talking, the display flashes everything at once. Marvel asks for a service diagnostic check.
Marvel ice machine display · also shown as all icons flashing
What to do when All indicators flashing shows on the ice machineKind of codeControl board and power
The board lost track of itself or of its power: a voltage too low or too high at startup, a relay that no longer closes, a keypad or display that stays dark, or a memory error after a surge. Switching off at the machine's own switch for a minute clears a passing glitch. A code that returns, a breaker that trips, or any hot or burning smell means the power stays off and the board, the wiring and the relays are left to a technician.
Usually leads toIce machine control board repair
The controller, its display, the sensors it reads and their wiring, tested when a code, a blinking light or a dead machine points there.
Shows up asIce Machine Error Code or Flashing Light: What It Is Telling You
An ice machine error code may show as a number on a small display, a pattern of blinking lights on the control board, a colored light on the front, or a machine that stops with one indicator flashing.
MakeMarvel
Marvel ice machine visits in a home start with the drain and the water supply, then move to the clear ice cycle.
SourceMarvel clear ice machine owner's guide (MACL215, MACP215, MLCL215, MLCP215, MOCL215, MOCP215, MP15CP)
Marvel Classic, Low Profile and Outdoor 15-inch clear ice machines with the ICE, ECO, OFF, DOOR and CLEAN word display (MLCL215/MLCP215, MACL215/MACP215, MOCL215/MOCP215 and the earlier MA15C, ML15C, MO15C, MP15C). The Professional MPCP415 uses a different numeric control.
Before you book,
in this order.
Each step comes from Marvel's own guidance for All indicators flashing on its ice machines. Follow it to the end: the last card says whether this is a visit.
Unplug the machine for a minute and plug it back in, then watch whether the flashing returns.
Keep water and cleaner off the control panel while wiping the machine.
If it returns, book a visit for a check of the harness and both boards.
Still there?
It usually turns into ice machine control board repair. Book with the code and the model number.
What not to do
This pattern is not a sensor signal, which flashes a single word, OFF or ICE. It is also not the control lock, where only the LOCK icon flashes three times.
What you may
notice with it.
The ice machine problems All indicators flashing tends to arrive with. Answer these at the ice machine before anyone is booked.
All problems
Where All indicators flashing usually leads
Ice machine control board repair.
Marvel
ice machines.
Marvel ice machine visits in a home start with the drain and the water supply, then move to the clear ice cycle.
Marvel ice machine repairMore Marvel codes
Control board and power on other makes
Undercounter ice machine
A self-contained ice machine that makes and stores its own ice under a bar, a service counter or a kitchen island, from commercial units to clear-ice models in large homes.
Nugget ice machine
An ice machine that freezes a thin layer inside a chilled cylinder and pushes it out with an auger as soft, chewable nuggets, for clinics, offices, hotels and large homes.
In Marvel's own words
Continual flashing of all indicators on the display.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Marvel Classic, Low Profile and Outdoor 15-inch clear ice machines with the ICE, ECO, OFF, DOOR and CLEAN word display (MLCL215/MLCP215, MACL215/MACP215, MOCL215/MOCP215 and the earlier MA15C, ML15C, MO15C, MP15C). The Professional MPCP415 uses a different numeric control.
Marvel All indicators flashing ice machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about All indicators flashing.
Can I clear All indicators flashing myself?
Can a power surge cause all the lights to flash on my Marvel ice machine?
Which board fails when a Marvel shows all indicators flashing?
Will my Marvel make ice while every indicator flashes?
Back to your everyday
Still showing All indicators flashing?
A booking with a code goes further when it carries the light or code copied as it appeared, the model and serial off the data plate, and a word on whether cubes still fall into the bin. With those three in hand, our office can match the probable part to your machine the same afternoon.