Blue Air E1: the ice machine froze too long twice and stopped
A Blue Air modular head gives each freeze up to 60 minutes.
Mon–Sat, 8am–8pm
- Harvest and freeze cycle
- Ice machine harvest repair
- Source: Blue Air
Book a visit
Three short steps, about a minute.
or call (844) 410-9163
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E1
actually means.
A Blue Air modular head gives each freeze up to 60 minutes. The first time it runs over, the machine moves on to harvest anyway; if the next freeze also runs over, it stops and shows E1. Blue Air's causes run from a refrigerant leak or blocked line and a compressor or fan motor that is not running, to air or water outside 45 to 100 F and 45 to 90 F, or voltage out of range.
Blue Air ice machine display
What to do when E1 shows on the ice machineKind of codeHarvest and freeze cycle
A freeze ran longer than the board allows, or a harvest started and the ice never fell. Scale on the evaporator holds the sheet to the plate, a thickness probe crusted with minerals never signals, a hot gas valve that does not open leaves the plate cold, a harvest assist that does not push, or a water curtain that swings without tripping its switch all end in this family. A cleaning cycle run by the manual often clears it; a valve or a probe is a technician's job.
Usually leads toIce machine harvest repair
The hot gas valve, harvest assist, curtain switch and thickness probe that decide when a sheet of cubes is done and make it drop.
Shows up asIce Machine Error Code or Flashing Light: What It Is Telling You
An ice machine error code may show as a number on a small display, a pattern of blinking lights on the control board, a colored light on the front, or a machine that stops with one indicator flashing.
MakeBlue Air
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
SourceBlue Air BLMI modular ice machine user manual (3rd generation evaporator)
BLMI-300A, BLMI-500A, BLMI-650A and BLMI-900A modular heads with the 3rd-generation evaporator (manual dated 220627), seven-segment display.
Before you book,
in this order.
Each step comes from Blue Air's own guidance for E1 on its ice machines. Follow it to the end: the last card says whether this is a visit.
Check that the condenser fan area is clear and the air filter is clean.
Make sure the room is between 45 and 100 F and nothing hot is blowing at the machine.
Restart the machine once and watch whether the fan and compressor come on.
If E1 returns, book a visit; a leak, compressor or voltage problem needs a technician.
Still there?
It usually turns into ice machine harvest repair. Book with the code and the model number.
What not to do
E1 on a BLMI head is not the same as E01 on the BLDN-280A dispenser, which uses a 30-minute limit. It is also not E3, which is an evaporator that got too warm during freezing.
What you may
notice with it.
The ice machine problems E1 tends to arrive with. Answer these at the ice machine before anyone is booked.
All problems
Where E1 usually leads
Ice machine harvest repair.
Blue Air
ice machines.
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
Blue Air ice machine repairMore Blue Air codes
Harvest and freeze cycle on other makes
Modular ice machine
An ice-making head set on top of a separate storage bin or drink dispenser, cooled by air, water or a condenser on the roof, turning out hundreds of pounds of cubes a day.
Undercounter ice machine
A self-contained ice machine that makes and stores its own ice under a bar, a service counter or a kitchen island, from commercial units to clear-ice models in large homes.
Nugget ice machine
An ice machine that freezes a thin layer inside a chilled cylinder and pushes it out with an auger as soft, chewable nuggets, for clinics, offices, hotels and large homes.
In Blue Air's own words
if time goes over 60 minutes, machine stops and shows error code (E1) on the control panel with a beep sound.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BLMI-300A, BLMI-500A, BLMI-650A and BLMI-900A modular heads with the 3rd-generation evaporator (manual dated 220627), seven-segment display.
Blue Air E1 ice machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E1.
Can I clear E1 myself?
Why does my Blue Air ice machine beep and show E1?
Can a hot room cause E1 on a Blue Air BLMI?
Does E1 on a Blue Air mean a refrigerant leak?
Back to your everyday
Still showing E1?
A booking with a code goes further when it carries the light or code copied as it appeared, the model and serial off the data plate, and a word on whether cubes still fall into the bin. With those three in hand, our office can match the probable part to your machine the same afternoon.