Blue Air E07: the ice dispenser control board memory reports an error
The dispenser's board stores its settings in a memory chip.
Mon–Sat, 8am–8pm
- Control board and power
- Ice machine control board repair
- Source: Blue Air
Book a visit
Three short steps, about a minute.
or call (844) 410-9163
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E07
actually means.
The dispenser's board stores its settings in a memory chip. When it cannot read or trust that memory, it shows E07; Blue Air traces it to the board's own software. No button blink pattern goes with it.
Blue Air ice machine display
What to do when E07 shows on the ice machineKind of codeControl board and power
The board lost track of itself or of its power: a voltage too low or too high at startup, a relay that no longer closes, a keypad or display that stays dark, or a memory error after a surge. Switching off at the machine's own switch for a minute clears a passing glitch. A code that returns, a breaker that trips, or any hot or burning smell means the power stays off and the board, the wiring and the relays are left to a technician.
Usually leads toIce machine control board repair
The controller, its display, the sensors it reads and their wiring, tested when a code, a blinking light or a dead machine points there.
Shows up asIce Machine Error Code or Flashing Light: What It Is Telling You
An ice machine error code may show as a number on a small display, a pattern of blinking lights on the control board, a colored light on the front, or a machine that stops with one indicator flashing.
MakeBlue Air
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
SourceBlue Air BLDN-280A countertop ice and water dispenser manual
BLDN-280A countertop nugget ice and water dispenser. The BLMI modular heads report a board problem as E7.
Before you book,
in this order.
Each step comes from Blue Air's own guidance for E07 on its ice machines. Follow it to the end: the last card says whether this is a visit.
Turn the dispenser off, wait a minute and turn it back on.
After the restart, check that the maximum dispensing time still behaves the way it was set.
If E07 returns, book a visit for the control board.
Still there?
It usually turns into ice machine control board repair. Book with the code and the model number.
What not to do
E07 is not a sensor or a water code, and it has no blinking button pattern. It is also not caused by anything in the ice or water.
What you may
notice with it.
The ice machine problems E07 tends to arrive with. Answer these at the ice machine before anyone is booked.
All problems
Where E07 usually leads
Ice machine control board repair.
Blue Air
ice machines.
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
Blue Air ice machine repairMore Blue Air codes
Control board and power on other makes
Modular ice machine
An ice-making head set on top of a separate storage bin or drink dispenser, cooled by air, water or a condenser on the roof, turning out hundreds of pounds of cubes a day.
Undercounter ice machine
A self-contained ice machine that makes and stores its own ice under a bar, a service counter or a kitchen island, from commercial units to clear-ice models in large homes.
Nugget ice machine
An ice machine that freezes a thin layer inside a chilled cylinder and pushes it out with an auger as soft, chewable nuggets, for clinics, offices, hotels and large homes.
In Blue Air's own words
E07 EEPROM error
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BLDN-280A countertop nugget ice and water dispenser. The BLMI modular heads report a board problem as E7.
Blue Air E07 ice machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E07.
Can I clear E07 myself?
What is an EEPROM error on a Blue Air dispenser?
Why are no buttons blinking with E07 on my Blue Air?
Is E07 on my Blue Air dispenser caused by the water or the ice?
Back to your everyday
Still showing E07?
A booking with a code goes further when it carries the light or code copied as it appeared, the model and serial off the data plate, and a word on whether cubes still fall into the bin. With those three in hand, our office can match the probable part to your machine the same afternoon.