Blue Air E6: the ice machine evaporator sensor is shorted or unplugged
The BLMI control times freeze and harvest from the evaporator sensor.
Mon–Sat, 8am–8pm
- Sensors and bin control
- Ice machine bin control repair
- Source: Blue Air
Book a visit
Three short steps, about a minute.
or call (844) 410-9163
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E6
actually means.
The BLMI control times freeze and harvest from the evaporator sensor. When that sensor is shorted or disconnected, the board cannot run the cycle and shows E6.
Blue Air ice machine display
What to do when E6 shows on the ice machineKind of codeSensors and bin control
A sensor is telling the board something that is not true: a bin control that reads full on an empty bin, or empty while ice spills over the top, a curtain switch stuck open, a temperature sensor out of range, or an eye on a dispenser that no longer sees the cup. Scale and slime on a probe or an ultrasonic sensor cause much of it. Clearing ice piled against the bin control is a safe first step; testing and replacing a sensor is a technician's.
Usually leads toIce machine bin control repair
The thermostat bulb, paddle, curtain switch or electronic eye that senses a full bin, adjusted or replaced so the machine stops and restarts on time.
Shows up asIce Machine Error Code or Flashing Light: What It Is Telling You
An ice machine error code may show as a number on a small display, a pattern of blinking lights on the control board, a colored light on the front, or a machine that stops with one indicator flashing.
MakeBlue Air
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
SourceBlue Air BLMI modular ice machine user manual (3rd generation evaporator)
BLMI modular heads, 3rd-generation evaporator (manual 220627).
Before you book,
in this order.
Each step comes from Blue Air's own guidance for E6 on its ice machines. Follow it to the end: the last card says whether this is a visit.
Switch the machine off and on once to rule out a one-time glitch.
If the machine was recently moved or serviced, mention it at booking, since a loose connector is a common result.
Book a visit so the sensor can be tested and swapped.
Still there?
It usually turns into ice machine bin control repair. Book with the code and the model number.
What not to do
E6 is not an evaporator that is really too hot; that is E3. It is also not the control board, which has its own code, E7.
What you may
notice with it.
The ice machine problems E6 tends to arrive with. Answer these at the ice machine before anyone is booked.
All problems
Where E6 usually leads
Ice machine bin control repair.
Blue Air
ice machines.
Blue Air ice machine calls start by reading the controls and looking at the evaporator for scale that slows the freeze.
Blue Air ice machine repairMore Blue Air codes
Sensors and bin control on other makes
Modular ice machine
An ice-making head set on top of a separate storage bin or drink dispenser, cooled by air, water or a condenser on the roof, turning out hundreds of pounds of cubes a day.
Undercounter ice machine
A self-contained ice machine that makes and stores its own ice under a bar, a service counter or a kitchen island, from commercial units to clear-ice models in large homes.
Nugget ice machine
An ice machine that freezes a thin layer inside a chilled cylinder and pushes it out with an auger as soft, chewable nuggets, for clinics, offices, hotels and large homes.
In Blue Air's own words
E6 Evaporator sensor error Sensor short-circuit or disconnected
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BLMI modular heads, 3rd-generation evaporator (manual 220627).
Blue Air E6 ice machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E6.
Can I clear E6 myself?
Can my Blue Air run with E6 on the display?
Is E6 on a Blue Air a board problem?
Is the evaporator sensor on a Blue Air a common repair?
Back to your everyday
Still showing E6?
A booking with a code goes further when it carries the light or code copied as it appeared, the model and serial off the data plate, and a word on whether cubes still fall into the bin. With those three in hand, our office can match the probable part to your machine the same afternoon.