Viking No Water and Drain lamps blinking: the bin-full sensor circuit is open or shorted
The bin sensor is a temperature sensor that feels the ice piling against it.
Mon–Sat, 8am–8pm
- Sensors and bin control
- Ice machine bin control repair
- Source: Viking
Book a visit
Three short steps, about a minute.
or call (844) 410-9163
Loading appointment form…
The appointment form couldn’t load. Please try again.
What NO WATER and DRAIN lamps blinking
actually means.
The bin sensor is a temperature sensor that feels the ice piling against it. If the control reads an open or shorted circuit, it cannot tell whether the bin is full, so it stops and blinks these two lamps; Viking's remedy is a sensor repair followed by a restart.
Viking ice machine display · also shown as Ice full sensor error
What to do when NO WATER and DRAIN lamps blinking shows on the ice machineKind of codeSensors and bin control
A sensor is telling the board something that is not true: a bin control that reads full on an empty bin, or empty while ice spills over the top, a curtain switch stuck open, a temperature sensor out of range, or an eye on a dispenser that no longer sees the cup. Scale and slime on a probe or an ultrasonic sensor cause much of it. Clearing ice piled against the bin control is a safe first step; testing and replacing a sensor is a technician's.
Usually leads toIce machine bin control repair
The thermostat bulb, paddle, curtain switch or electronic eye that senses a full bin, adjusted or replaced so the machine stops and restarts on time.
Shows up asIce Machine Error Code or Flashing Light: What It Is Telling You
An ice machine error code may show as a number on a small display, a pattern of blinking lights on the control board, a colored light on the front, or a machine that stops with one indicator flashing.
MakeViking
A Viking ice machine call covers the panel-ready install, the drain and the water side before the cooling system is looked at.
SourceViking FNIU515D nugget ice machine Install / Use & Care manual
Viking FNIU515D nugget ice machine.
Before you book,
in this order.
Each step comes from Viking's own guidance for NO WATER and DRAIN lamps blinking on its ice machines. Follow it to the end: the last card says whether this is a visit.
Look inside the bin for anything pressing on or pulling at the sensor or its wire, such as the scoop or a clump of ice.
Turn the machine off and on once.
If the two lamps blink again, book a visit to test and replace the sensor.
Still there?
It usually turns into ice machine bin control repair. Book with the code and the model number.
What not to do
This is not a water supply or drain problem, even though those two lamps are the ones that blink. A single blinking No Water lamp is Er15 and a single blinking Drain lamp is Er16.
What you may
notice with it.
The ice machine problems NO WATER and DRAIN lamps blinking tends to arrive with. Answer these at the ice machine before anyone is booked.
All problems
Where NO WATER and DRAIN lamps blinking usually leads
Ice machine bin control repair.
Viking
ice machines.
A Viking ice machine call covers the panel-ready install, the drain and the water side before the cooling system is looked at.
Viking ice machine repairMore Viking codes
Sensors and bin control on other makes
Undercounter ice machine
A self-contained ice machine that makes and stores its own ice under a bar, a service counter or a kitchen island, from commercial units to clear-ice models in large homes.
Nugget ice machine
An ice machine that freezes a thin layer inside a chilled cylinder and pushes it out with an auger as soft, chewable nuggets, for clinics, offices, hotels and large homes.
In Viking's own words
When the ice full temperature sensor in the storage bin is disconnected or shorted
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Viking FNIU515D nugget ice machine.
Viking NO WATER and DRAIN lamps blinking ice machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about NO WATER and DRAIN lamps blinking.
Can I clear NO WATER and DRAIN lamps blinking myself?
Why would my Viking blink No Water and Drain when the water is fine?
Can a Viking with a bad bin sensor overfill the bin?
Is the Viking bin sensor something I can replace myself?
Back to your everyday
Still showing NO WATER and DRAIN lamps blinking?
A booking with a code goes further when it carries the light or code copied as it appeared, the model and serial off the data plate, and a word on whether cubes still fall into the bin. With those three in hand, our office can match the probable part to your machine the same afternoon.